Line cleaning, training, repairs

Draught system maintenance and servicing

Line cleaning comes after brewery projects and equipment. You clean the lines yourself: we equip you and train your staff on site. Or we come to you, regularly or as a one-off, for line cleaning, adjustments and repairs, quoted.

You clean the lines yourself

We equip you and train your staff

Within a few days, deposits build up in beer lines: yeast, bacteria, hop resin and protein, minerals. Left alone, they change the taste of the beer. Your staff can clean the lines themselves between services, with the right equipment and the right routine.

  • Cleaning equipment

    A line cleaning machine or a cleaning keg, alkaline and acid cleaners, cleaning sockets and tap brushes, chosen for your system and your kegs. A cleaning socket takes the place of the keg: the coupler, which normally connects to the keg, fits onto it to run water, then cleaner, through the line. See the cleaning and sanitation range on the equipment page.

  • On-site training

    We train your staff at your venue, on your own system: emptying the lines, running the cleaner through, taking the taps apart and cleaning them, scrubbing the couplers, rinsing until no cleaner is left.

  • A written procedure

    Your staff keep a procedure sheet: the steps in order, the products used, the protection to wear and the cleaning schedule agreed with you.

Request a training quote

Guidelines

How often to clean

These guidelines come from the Draught Beer Quality Manual (2017 edition) of the Brewers Association, the American association of independent brewers. They are good practice, not a visit commitment: the schedule is agreed with you, whether your staff clean or we visit, based on your beers, how much you pour and your system.

  • Every two weeks

    Lines cleaned with an alkaline cleaner. Taps taken apart and cleaned, couplers scrubbed, FOB detectors cleaned in line.

  • Every three months

    An acid clean on top of the alkaline clean. It removes beer stone, a mineral deposit that builds up slowly and is hard to shift.

  • Every six months

    FOB detectors and couplers fully taken apart and cleaned by hand.

  • Every one to two years

    Vinyl jumper hoses between the keg and the system replaced, along with the vinyl lines of an under-counter system.

We do it for you

Regular or one-off visits

We visit on the schedule agreed with you, or when you need us. We work in Belgium in Brussels and Walloon Brabant, and in France in Hauts-de-France and Paris. Travel is quoted according to how often we visit.

  • Line cleaning

    The lines are run through with cleaner, then rinsed with clean water. Taps are taken apart and cleaned, keg couplers scrubbed, FOB detectors cleaned. The FOB detector shuts the line when the keg runs empty, before foam fills it.

  • Adjustments

    Pressure or temperature that drifts makes the beer foam at the tap. Gas pressure, temperature and flow, tap by tap: we adjust the system so the beer pours at the right temperature, without excess foam.

  • Repairs

    A leak, beer that foams or pours warm, a cooler that no longer cools: you report the fault, we diagnose it, then we schedule the visit.

How a visit goes

What a visit includes

  1. Empty the lines

    The kegs are disconnected and the beer left in the lines is pushed out with water.

  2. Clean

    An alkaline cleaner circulates through each line, followed by an acid clean when one is due. Meanwhile, the taps are taken apart and cleaned by hand and the couplers scrubbed.

  3. Rinse

    The lines are rinsed with clean water until no cleaner is left, which we check before reconnecting the kegs.

  4. Adjust and check

    With the kegs back on, we check the beer temperature at the tap, the CO2 pressure, the flow and every connection for leaks, and adjust whatever needs it.

  5. Hand over the sheet

    You receive the service sheet: what was done, what was checked, what to watch. A repair visit ends the same way: tests, then the sheet.

After every visit

The service sheet

Cleaning, adjustment or repair: every visit leaves a service sheet, signed with you. It keeps the history of your system, visit after visit.

  • What was done

    The equipment involved and its serial number, the reason for the visit, the diagnosis, the parts replaced.

  • What was checked

    The tests and their measured values: beer temperature at the tap, CO2 pressure, flow, leaks in the circuit.

  • What to watch

    Any reservations, and the point to keep an eye on at the next visit.

When something breaks

Repairs in writing, then scheduled

No emergency call-outs or on-call service. Report the fault in writing within 10 days of it appearing (terms and conditions, article 9.3), through the form, by email or on WhatsApp, with a photo or video: it helps the diagnosis.

We reply within 48 working hours and schedule the visit. If the fault isn't covered by article 9 of the terms and conditions, the visit is quoted first. Article 9 excludes, among other things, normal wear and lack of maintenance.

Warranties: article 9 of the terms and conditions, without prejudice to statutory warranties.

Over time

Ongoing maintenance, if you want it

We can look after your system over time, with a maintenance contract quoted for your system: number of taps, length of the lines, the beers you pour, the pace of your service. What it covers and how often we visit are agreed with you in the quote.

For used equipment bought from us, the cover under article 9.2 of the terms and conditions goes from 3 to 6 months with a maintenance contract.

Request a maintenance quote

Frequently asked questions

How often should beer lines be cleaned?

The Brewers Association manual recommends every two weeks, with an acid clean every three months. It's a guideline, not a commitment: we agree the schedule with you, based on your beers, how much you pour and your system.

Can I clean my lines myself?

Yes, and it's what we suggest first. We supply the cleaning equipment (cleaning machine or keg, cleaners, cleaning sockets, brushes) and train your staff on site, with a procedure sheet. Equipment and training are quoted.

Can you come the same day?

No. No emergency call-outs or on-call service. We reply within 48 working hours and schedule the visit.

What should I do if something breaks?

Report the fault in writing within 10 days of it appearing, with a photo or video. We schedule the visit, quoted first if the fault isn't covered by article 9 of the terms and conditions of sale.

How much does maintenance cost?

It's quoted, excluding VAT, like the cleaning equipment and the training. The price of visits depends on the number of taps, the length of the lines, how often we come and the distance.

Do you come if my venue is far away?

Yes. We work in Belgium in Brussels and Walloon Brabant, and in France in Hauts-de-France and Paris. Travel is quoted according to how often we visit. You can also clean the lines yourself: we train your staff on site.

Who replies

Tell us about your system

I reply within 48 working hours and call you back at the time slot you choose. Tell me how many taps you pour, when the lines were last cleaned and what's wrong, with a photo or video.

Arthur Chrétien, Pipeline